As well as being unbeatable on price, the SlipGrip Standard Flat Sheets also maintain the excellent quality of the SlipGrip range. Best used to make slippery walkways and ramps safe, our Standard Flat Sheets are a general purpose, tough GRP suitable for both industrial and commercial use.
Stock Code:SGSFS0.8X1.2B
Why Choose SlipGrip Standard Flat Sheets?
Standard | Heavy Duty | |
Grit Type: | Standard | ExtremeCore® |
MOHS Hardness Scale: | 7 | 9 |
Ideal For: | Commercial premises | Industrial premises |
PTV Test Reading Dry: | 71 | 76 |
PTV Test Reading Wet: | 63 | 70 |
Traffic Level: | Medium | Heavy |
Prices From: | £30.40 | £60.18 |
Sheet Thickness: | 4mm - 5mm with grit | 5mm - 7mm with grit |
Guarantee: | 3 Years | 10 Years |
How to Install
You can install our SlipGrip Standard Flat Sheets easily and quickly with our SlipGrip GRP Flooring Sheet Fixing Kits. 1 fixing kit covers 1 full 2400mm x 1200mm sheet.
Preparation
Ensure that the area is clean, dry and free from loose and friable material. Any “dished” or damaged surface areas should be patch repaired to provide a reasonably flat and consistent surface.
Dry fit all SlipGrip panels to ensure they fit freely and that they sit flat down on the surface. If required, SlipGrip can be trimmed on site to suit, ideally using a skill saw with a 4mm diamond blade or an angle grinder with a 1mm blade.
Please ensure that goggles and gloves are worn at all times when any form of cutting is involved.
Fixing Kit Application
Apply an approx. 6mm bead (this may need to be increased dependant on the substrate conditions) of the high strength gap filling adhesive around the periphery of the underside of the SlipGrip panels approx. 25mm in from the edges. Then, starting from the bottom left corner come up at an angle (approx. 200mm across) and then down at an angle, to create a ‘peak and a trough’, repeat this until you reach the end. Immediately press the panel firmly to the substrate to ensure adequate transfer of adhesive (depending on the size of the bead, this will elevate the sheet by approximately 1-1.5mm). A firm bond will be achieved in about one hour under normal circumstances and conditions. Secure with mechanical fixings, as below.
Drill holes 50mm in from all edges at no more than 300mm apart from the centres. Depending on the width of the panels it may be necessary to provide fixing points at 600mm centres down the middle of the panels. As substrates vary considerably, additional fixings may be required to fix the panels down. If fixing down two pieces of flat sheet that is constrained by sides (i.e. a ramp with wall on either side) a 5mm expansion gap should be considered between the two or more sheets. This gap can be filled with a standard high modulus mastic.
Sizes
Colours
Prices shown are excluding VAT. Please note this is an all day courier delivery service and is not guaranteed. Please refer to point 6 of our terms and conditions for full details.
Order Value | United Kingdom Mainland |
£100 and under | £9.95 |
£100.01 to £300 | £16.00 |
£300.01 to £500 | £25.00 |
£500.01 to £750 | £35.00 |
£750.01 to £1000 | £42.00 |
£1001.01 to £1500 | £52.00 |
£1500.01 to £2000 | £67.00 |
£2000.01 to £3000 | £95.00 |
£3000.01 to £4000 | £120.00 |
£4000.01 and over | £300.00 |
Order Value | Highlands and Islands* |
£100 and under | £45.00 |
£100.01 to £500 | £100.00 |
£500.01 to £1000 | £200.00 |
£1000.01 to £3000 | £280.00 |
£3000.01 and over | £300.00 |
Order Value | Europe Zone 1 & Northern Ireland** |
£100 and under | £45.00 |
£100.01 to £3000 | £150.00 |
£3000.01 to £6000 | £250.00 |
£6000.01 and over | Please call 01440 712722 for a bespoke quote. |