SlipGrip Anti Slip GRP Stair Landing Covers

SlipGrip Anti Slip GRP Stair Landing Covers make landings, walkways and balconies anti slip, and perfectly complement SlipGrip Stair Tread Covers.

Stock Code:SGLC0.8X1.2W

Why Choose SlipGrip Anti Slip GRP Stair Landing Covers?


  • Heavy duty - our landing covers are produced using our own ExtremeCore™ grit, which is twice as hard wearing as the industry standard quartz, thus guaranteeing many more years of use than those of our competitors.
  • Their 55mm contrasting nosing also makes them Building Regulation and Disability Discrimination Act compliant.
  • Suitable for - landings, walkways and balconies both internally and externally. Our stone landing cover is also suitable for areas where looks are important, such a heritage sites, golf clubs and other commercial venues.

How to Install



  • Ensure that the area is clean, dry and free from loose and friable material. Any “dished” or damaged surface areas should be patch repaired to provide a reasonably flat and consistent surface. You can patch repair concrete with our SlipGrip Step Edge Repair.

  • Dry fit landing covers to ensure they fit freely and that they sit flat down on the surface. If required, SlipGrip can be trimmed on site to suit, ideally using a skill saw with a 4mm diamond blade or an angle grinder with a 1mm blade.

  • Please ensure that goggles and gloves are worn at all times when any form of cutting is involved.


Fixing Kit Application

  • Apply an approx. 6mm bead (this may need to be increased dependent on the substrate conditions) of the high strength gap filling adhesive around the periphery of the underside of the stair tread cover section of the landing cover approx. 25mm in from the edges. Then, do the same with the flat sheet section of the landing cover.

  • Then, starting from the bottom left corner of the stair tread section, come up at an angle (approx. 200mm across) and then down at an angle, to create a ‘peak and a trough’, repeat this until you reach the end. Do the same for the flat sheet section of the landing cover - create a peak and trough adhesion across the sheet.

  • Immediately press the landing cover firmly to the substrate to ensure adequate transfer of adhesive (depending on the size of the bead, this will elevate the sheet by approximately 1-1.5mm). A firm bond will be achieved in about one hour under normal circumstances and conditions.

  • Drill holes 15mm in from all edges at no more than 300mm apart from the centres. Depending on the width of the panels it may be necessary to provide fixing points at 600mm centres down the middle of the panels. As substrates vary considerably, additional fixings may be required to fix the panels down. If fixing down two pieces of landing covers that is constrained by sides (i.e. a ramp with wall on either side) a 5mm expansion gap should be considered between the two or more sheets. This gap can be filled with a standard high modulus mastic.


SlipGrip Anti Slip GRP Stair Landing Covers can come with pre-drilled holes for which there is a surplus. If you require the holes in a certain place please call 01440 712722.

Technical Data Sheet

Mechanical Data Sheet



Stock Sizes

  • Width: 800mm, 1200mm, or 2400mm
  • Depth: 1200mm (including the 55mm nosing)
  • Thickness: 4mm with grit
  • Nosing Angle: 85°


  • Black with Yellow Nosing
  • Black with White Nosing
  • Grey with Yellow Nosing
  • All Stone
  • Call 01440 712722 if you would like bespoke colours.

Prices shown are excluding VAT. Please note this is an all day courier delivery service and is not guaranteed. Please refer to point 6 of our terms and conditions for full details.


Order Value United Kingdom Mainland
£100 and under £9.95
£100.01 to £300 £16.00
£300.01 to £500 £25.00
£500.01 to £750 £35.00
£750.01 to £1000 £42.00
£1001.01 to £1500 £52.00
£1500.01 to £2000 £67.00
£2000.01 to £3000 £95.00
£3000.01 to £4000 £120.00
£4000.01 and over £300.00


Order Value Highlands and Islands*
£100 and under £45.00
£100.01 to £500 £100.00
£500.01 to £1000 £200.00
£1000.01 to £3000 £280.00
£3000.01 and over £300.00


Order Value Europe Zone 1 & Northern Ireland**
£100 and under £45.00
£100.01 to £3000 £150.00
£3000.01 to £6000 £250.00
£6000.01 and over Please call 01440 712722 for a bespoke quote.


* Highlands and Islands include - the Scottish Highlands and Islands, Isle of Wight, Isle of Man and the Channel Islands. ** Countries included in Europe Zone 1 - Southern Ireland, France, Germany, Luxembourg, Netherlands & Belgium. For all deliveries outside Europe Zone 1, please call 01440 712722 to place your order.